Balboa-water-group VGB 2008 211 GPM Suction Flow User Manual download pdf

VGB 2008

211 GPM Suction Flow

Installation Instructions

For single or multiple use submerged suction outlet. 1.

Do not try to locate suction outlets on seating areas or on the brackets for such seating areas. 2.

When two or more suction ﬁttings are used on a common suction line they shall be separated by a minimum of 3 ft. (91.44 cm), or, 3.

if any are located closer they shall be located on two different planes (i.e., one each on two separate vertical walls). Conﬁrm with

local and national codes and standards for proper installation.

In the event of one suction outlet being completely blocked, the remaining suction outlets serving that system shall have a ﬂow 4.

rating capable of the full ﬂow of the pump(s) for the speciﬁc suction system.

Maximum ﬂow rating with head loss curve: 211 GPM. 5.

Acceptable connecting pipe size(s) - maximum 2.5.” 6.

Mounting position: wall only 7.

Suction outlet part number 30231 U applicable. 8.

Part numbers: 9.

30231 U VGB 2008 211 GPM SUCTION COVER & SCREW/UV (replace within seven installed years)

30341 VGB 2008 BUTTRESS SUCTION WALL FITTING X CUSTOM SLIP (replace within seven installed years)

30234-V SUCTION L-GASKET USE 3.75” HOLE SIZE (replace within seven installed years)

30236-V SUCTION FLAT GASKET (replace within seven installed years)

30238-V SUCTION COMPENSATING RING (replace within seven installed years)

63414 3/4” ID x 1” OD TUBING 8-FT LONG (replace within seven installed years)

30239-V SUCTION NUT (replace within seven installed years)

30167-V 2”SPG X CUSTOM SPG X 3/4” SMOOTH BARB SAFETY SUCTION ADAPTER (replace within seven installed years)

30169-V 2 1/2”SPG X CUSTOM SPG X 3/4” SMOOTH BARB SAFETY SUCTION ADAPTER (replace within seven installed years)

Tools required: Philips screw driver, glue for plumbing connections, clamp & pliers for tubing connections. 10.

Service and winterizing instructions. 11.

a. Service - remove screw. Remove cover. Place suction cover on wall ﬁtting with blank portion, no holes pointed down.

The keyway on inside cover must match the notch on the wall ﬁtting. Insert stainless steel screw in cover and tighten

securely. Do not overtighten (as plastic will strip).

b. Winterizing - Drain suction line thoroughly and blowout all remaining water. See spa manufacturer instructions

for winterizing.

WARNING: Do not exceed the maximum allowable ﬂow rate stated on the suction ﬁtting. 12.

The suction ﬁtting including fasteners should be observed for damage or tampering before each use of this facility. 13.

Note: Missing, broken, or cracked suction ﬁttings shall be replaced before using this facility. Loose suction ﬁttings shall be reat-

tached or replaced before using this facility. Read, then keep these instructions for future reference.

Caution: Be aware that changing pump types and sizes can increase ﬂow rate. The maximum ﬂow rate is 211 GPM.

Instructions

40747 Rev A May 21, 2012

1 2

Summary of Contents

Page 1 - Instructions

VGB 2008 211 GPM Suction Flow Installation InstructionsFor single or multiple use submerged suction outlet. 1. Do not try to locate suction outlets

Page 2

Step OneDo not locate suction outlets on seating areas or on the brackets for such areas. Step TwoCut a 3.5” hole into the spa wall for a ﬂat gasket.C

Comments to this Manuals

No comments

Balboa-water-group VGB 2008 211 GPM Suction Flow User Manual

Browse online or download User Manual for Accessories for water Balboa-water-group VGB 2008 211 GPM Suction Flow. Balboa Water Group VGB 2008 211 GPM Suction Flow User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Accessories for water Balboa-water-group VGB 2008 211 GPM Suction Flow